Attic Ventilation (1/150 and 1/300) and Asphalt Shingle Basics in the 2024 IRC

Worked attic ventilation math under IRC 2024 Section R806.2 (1/150 and the 1/300 exception) plus asphalt shingle slope, underlayment, fasteners and drip edge from R905.2.

Code references covered

IRC 2024 Sections R806.1, R806.2, R806.3 · IRC 2024 Section R807.1 · IRC 2024 Sections R905.1.1, R905.1.2 · IRC 2024 Sections R905.2.1, R905.2.2, R905.2.5, R905.2.6 · IRC 2024 Section R905.2.8.5

Checked against the 2024 IRC (Second Printing) on 2026-11-14. Confirm the edition your exam and jurisdiction use, and any local amendments.

Attic ventilation and asphalt shingles are two of the most common roof inspections, and both reduce to a few numbers you can find quickly: a ventilation ratio in IRC 2024 Section R806.2 and a short list of shingle checks in Section R905.2. This guide works through both.

Attic ventilation (R806)

The basic requirement

Section R806.1 requires cross ventilation for each enclosed attic and enclosed rafter space. Vent openings must have a least dimension between 1/16 inch and 1/4 inch, or be covered with screening in that range, and must keep out rain, snow, birds and rodents.

Section R806.2 sets the amount: the net free ventilating area must be at least 1/150 of the area of the vented space. “Net free” means the open area after louvers and screens, which is why vent products are rated in net free area rather than by their outside size.

Worked example 1 — the 1/150 ratio

A 30-by-50-foot attic is 1,500 square feet. 1,500 ÷ 150 = 10 square feet of net free area, or 1,440 square inches. Add up the rated net free area of every soffit, gable and ridge vent and compare it to that number.

The 1/300 exception

The exception to Section R806.2 lets the ratio drop to 1/300, but only when both of its conditions are met:

  1. In Climate Zones 6, 7 and 8, a Class I or Class II vapor retarder is installed on the warm-in-winter side of the ceiling.
  2. Not less than 40% and not more than 50% of the required ventilating area is provided by upper vents located no more than 3 feet below the ridge or highest point, measured vertically, with the rest in the bottom one-third of the attic. (The exception allows upper vents lower where framing gets in the way.)

Worked example 2 — the 1/300 ratio

Same 1,500-square-foot attic: 1,500 ÷ 300 = 5 square feet (720 square inches). Between 40% and 50% of that — 2 to 2.5 square feet — must be high vents within 3 feet of the ridge, and the balance low, typically at the soffits. If all the vents are at the soffits, the exception is not met and the full 10 square feet is required.

Related attic checks

  • Section R806.3 — at eave or cornice vents, insulation and blocking may not block airflow, and at least a 1-inch space is required between the insulation and the roof sheathing at the vent.
  • Section R806.5 — unvented attics are allowed under a separate set of conditions; do not mix those rules with R806.2.
  • Section R807.1 — an attic with at least 30 inches of vertical height over at least 30 square feet needs an access opening of at least 22 by 30 inches, with 30 inches of headroom above a ceiling access.

Asphalt shingles (R905.2)

CheckSectionWhat to verify
DeckR905.2.1Wood structural panels or solid lumber sheathing
SlopeR905.2.22:12 minimum; double underlayment from 2:12 up to 4:12
UnderlaymentR905.2.3, R905.1.1Type, application and fastening per Tables R905.1.1(1)–(3)
Ice barrierR905.2.7, R905.1.2Where Table R301.2 calls for it
FastenersR905.2.512-gage shank, 3/8-in. head, 3/4 in. into the deck or through it
Fastener countR905.2.6At least four per strip shingle, or the manufacturer's number if higher
Drip edgeR905.2.8.5At eaves and rakes; 2-in. laps; fastened at 12 in. o.c. or less

Worked example 3 — low-slope shingle roof

A porch roof is pitched at 3:12. Asphalt shingles are allowed because the slope is at least 2:12, but because it is under 4:12 the underlayment must be applied as a double layer. At 1 1/2:12, asphalt shingles are not permitted at all.

Ice barrier

Where the jurisdiction's Table R301.2 shows a history of ice damming, Section R905.1.2 requires an ice barrier from the lowest edge of the roof to a point at least 24 inches inside the exterior wall line. On roofs of 8:12 or steeper, it must extend at least 36 inches along the slope from the eave edge. Detached accessory structures without conditioned floor area are exempt. A wide overhang therefore means a wider ice barrier, because the 24 inches is measured inside the wall line, not from the eave.

Drip edge

Section R905.2.8.5 requires drip edge at eaves and rakes, extending at least 1/4 inch below the sheathing and at least 2 inches back onto the deck. The underlayment goes over the drip edge at the eaves and under it at the rakes — a detail inspectors can see from a ladder.

The rafters and ceiling joists under all this are sized with the span tables. For the full list of B1 content areas, see the B1 exam overview.

For the exact code language, read the sections on the official ICC Digital Codes site. We cite section identifiers and explain the logic in our own words — always confirm the current text and any local amendments there.

Want to practice this topic under exam conditions?

B1 practice questions built on the 2024 IRC are in development. Join the waitlist and we'll email you when they open.

Free. We'll email you when B1 practice opens.

Also preparing for another exam? Try 10 free M1 questions · Try 10 free P1 questions

Related guides

Frequently asked questions

How much attic ventilation does the IRC require?
Section R806.2 requires a net free ventilating area of at least 1/150 of the vented space. A 1,500-square-foot attic therefore needs 10 square feet of net free area.
When can attic ventilation be reduced to 1/300?
Only when both conditions in the R806.2 exception are met: in Climate Zones 6, 7 and 8 a Class I or II vapor retarder is on the warm-in-winter side of the ceiling, and 40 to 50 percent of the required area is in upper vents within 3 feet of the ridge, with the rest in the bottom third of the attic.
What is the minimum roof slope for asphalt shingles?
Section R905.2.2 allows asphalt shingles on slopes of 2:12 or greater. From 2:12 up to 4:12, a double underlayment application is required.