Drainage Fixture Units (d.f.u.) Explained, with Worked Examples

How to total drainage fixture units with IRC 2024 Table P3004.1: individual fixtures, bath, kitchen and laundry groups, multiple-bath groups, note c, and the P3005.4 procedure.

Code references covered

IRC 2024 Section P3004.1 · IRC 2024 Table P3004.1 · IRC 2024 Section P3005.4 · IRC 2024 Section P3005.1.5

Checked against the 2024 IRC (Second Printing) on 2026-11-06. Confirm the edition your exam and jurisdiction use, and any local amendments.

Every drain-sizing question on the P1 starts with the same step: turn the fixtures into a load. The IRC measures drainage load in drainage fixture units (d.f.u.). IRC 2024 Section P3004.1 says the load on DWV piping is computed with the values in Table P3004.1. This guide shows how to read that table, when to use group values instead of individual fixtures, and what the three table notes do.

What a d.f.u. is (and is not)

A drainage fixture unit is not gallons or gallons per minute. It is a relative load that accounts for how much a fixture discharges, how fast, and how likely it is to drain at the same time as other fixtures. That last part is why a group of fixtures is often worth less than the sum of its parts.

Individual fixtures and groups

Table P3004.1 lists individual fixtures and fixture groups. A few values you will see a lot:

Fixture or group (Table P3004.1)d.f.u.
Lavatory1
Bar sink1
Bathtub, shower stall, kitchen sink, dishwasher, laundry tub, clothes washer standpipe2 each
Water closet, 1.6 gallons per flush3
Full-bath group with bathtub (1.6 gpf water closet)5
Half-bath group (1.6 gpf water closet plus lavatory)4
Kitchen group (sink and dishwasher, with or without disposer)2
Laundry group (washer standpipe and laundry tub)3
Floor drain (see note b)0

Water closets that use more than 1.6 gallons per flush carry higher values (4 for the water closet, 6 for the full-bath group, 5 for the half-bath group), so read the flush volume in the question.

Multiple-bath groups

The most useful rows are at the bottom of the table: multiple-bath groups for 1.5, 2, 2.5, 3 and 3.5 baths, valued at 7, 8, 9, 10 and 11 d.f.u. Step 3 of the drain sizing procedure in Section P3005.4 tells you to use these reduced values where multiple bath groups are being added, because they account for the probability of simultaneous use.

Example 1 — Two full baths

Added one by one, two full-bath groups would be 5 + 5 = 10 d.f.u. Using the multiple-bath group for 2 baths gives 8 d.f.u. On a downstream pipe that carries both bathrooms, 8 is the value to use.

Note c: more baths than the table lists

The table stops at 3.5 baths. Note c covers larger houses: add 2 d.f.u. for each additional full bath.

Example 2 — Four and a half baths

Start from 3.5 baths = 11 d.f.u. The house has one more full bath, so add 2: 11 + 2 = 13 d.f.u. for the bathrooms. Kitchen, laundry and any other fixtures are added on top.

Note b: floor drains

A floor drain on its own is listed at 0 d.f.u. because it does not add hydraulic load. But when a floor drain is used as a receptor, you count the fixture that discharges into it. If a fixture drains indirectly to a floor drain, the load is the fixture's value, not zero.

Note a: pumps and unlisted fixtures

For continuous or semicontinuous flow, such as a pump discharging into the drainage system, note a assigns 1.5 d.f.u. per gpm of flow. For a fixture that is not listed, use the highest value of a similar listed fixture.

Example 3 — A pumped discharge

A device discharges continuously at 4 gpm into a branch. Under note a it adds 4 × 1.5 = 6 d.f.u. to that branch and everything downstream.

Putting a whole house together

Example 4 — Whole-house load

A house has 2.5 baths (1.6 gpf water closets), a kitchen sink with dishwasher, a laundry with a washer standpipe and laundry tub, and a bar sink.

  • 2.5 baths, multiple-bath group: 9 d.f.u.
  • Kitchen group: 2 d.f.u.
  • Laundry group: 3 d.f.u.
  • Bar sink: 1 d.f.u.

Total on the building drain: 9 + 2 + 3 + 1 = 15 d.f.u. The next step is sizing, covered in sizing horizontal branches, stacks and the building drain.

Work downstream, branch by branch

Section P3005.4 lays out a general procedure: draw an isometric or riser diagram, assign d.f.u. values to groups and individual fixtures, then start at the top floor or the most remote fixture and add up the load as you move downstream. Each branch and stack is sized for the load it actually carries; the building drain and sewer are sized for the total. The size may not be reduced in the direction of flow. Rough-ins for future fixtures count too — Section P3005.1.5 requires their d.f.u. values to be included when sizing.

Inspector checklist

  • Use group values when a whole bathroom, kitchen or laundry drains through the pipe in question.
  • Use the multiple-bath rows (and note c) only where several bath groups combine.
  • Check the flush volume before choosing the water closet or bath-group row.
  • Count fixtures discharging to a floor drain receptor; the floor drain itself is 0.
  • Include roughed-in future fixtures.

For the exact code language, read the sections on the official ICC Digital Codes site. We cite section identifiers and explain the logic in our own words — always confirm the current text and any local amendments there.

Practice this topic with 2024 IRC-based P1 questions

Create a free account to practice P1 questions with written explanations and 2024 IRC references.

Related guides

Frequently asked questions

How many d.f.u. is a house with four and a half baths?
Table P3004.1 lists multiple-bath groups up to 3.5 baths (11 d.f.u.). Note c adds 2 d.f.u. for each additional full bath, so 3.5 baths plus one more full bath is 11 + 2 = 13 d.f.u. for the bathrooms. Kitchen, laundry and other fixtures are added on top.
Does a floor drain count toward the drainage load?
A floor drain by itself is 0 d.f.u. (Table P3004.1 note b). Where it serves as a receptor, use the d.f.u. value of the fixture that discharges into it.