How to Find a Plumbing Section Fast in the 2024 IRC (Chapter Map)

A chapter map of the 2024 IRC plumbing provisions (Chapters 25–32) plus the Chapter 20 and Chapter 24 parts that cover water heaters, with a fast lookup method for the P1.

Code references covered

IRC 2024 Chapters 25–32 · IRC 2024 Section M2005 · IRC 2024 Sections G2407, G2427, G2448 · IRC 2024 Sections R326, R327 · IRC 2024 Sections P2503, P2605, P2902 · IRC 2024 Sections P3005.3, P3113.1

Checked against the 2024 IRC (Second Printing) on 2026-11-06. Confirm the edition your exam and jurisdiction use, and any local amendments.

On a 60-question, 2-hour open-book exam, the fastest candidates are not the ones who know the most numbers. They are the ones who can open the 2024 IRC to the right chapter on the first try. This guide gives you a chapter map for everything the P1 covers and a simple method to go from a question to the controlling section.

How plumbing sections are numbered

The plumbing provisions sit in Part VII of the IRC. Every plumbing section starts with “P”, and the first two digits after the P are the chapter: P2503 is in Chapter 25, P3105 in Chapter 31, P3201 in Chapter 32. Tables are named after the section they belong to, so Table P3005.4.1 is inside Section P3005.4. Once that clicks, a section number in a question tells you exactly where to open the book.

The chapter map

ChapterTitleWhat you look up there
25Plumbing AdministrationPlumbing scope, existing systems, inspection and tests (P2503)
26General Plumbing RequirementsProtection of piping and structure, trenching, support, penetrations, workmanship
27Plumbing FixturesFixtures, fittings, waste receptors and standpipes, showers, water closets
28Water HeatersDrain valves, pans, garages, relief valves and discharge piping (P2804)
29Water Supply and DistributionBackflow protection, pressure, fixture units, manifolds, valves, materials
30Sanitary DrainageDWV materials and joints, d.f.u., drain sizing, cleanouts, sumps, backwater valves
31VentsVent terminals, grades, trap-to-vent distance, venting methods, vent sizing, AAVs
32TrapsTrap seals, prohibited traps, fixtures per trap, trap sizes

Chapter 33, Storm Drainage, follows Chapter 32, but storm drainage is not one of the six P1 content areas. Do not let it pull you in just because it sits next to the plumbing chapters. The same goes for Section P2904, dwelling-unit fire sprinklers, which sits inside Chapter 29 but is not a P1 area.

Where to look: common P1 question types

Most P1 questions fall into a short list of recurring types. The table below pairs each type with the section or table that answers it and the detail that most often decides the answer. It is a navigation aid, not a substitute for reading the section.

Question typeGo toWhat to check there
Drainage load of a fixture or groupTable P3004.1Group values versus individual fixtures, and the table notes
Size a horizontal branch or a stackSection P3005.4.1, Table P3005.4.1Below-grade drains at least 1 1/2 in.; a stack is never smaller than the largest branch connected
Size the building drain or sewerSection P3005.4.2, Table P3005.4.2Size and slope are read together
Minimum slope of a horizontal drainSection P3005.31/4 in. per foot up to 2 1/2 in.; 1/8 in. per foot for 3 in. and larger
Trap-to-vent distance (trap arm)Section P3105.1, Table P3105.1Trap size and slope; the exception for self-siphoning fixtures such as water closets
Trap size for a fixtureSection P3201.7, Table P3201.7The fixture row, and what the section says about tailpieces
Vent sizeSection P3113.1At least half the required drain diameter, never under 1 1/4 in., one size larger past 40 ft developed length
Water supply load and demandTable P2903.7, Table P2903.7(1)Hot, cold or combined column; flush-tank or flushometer half
Relief valves and discharge pipingSection P2804, Section P2804.6.1The numbered list of discharge pipe requirements
Water heater panSection P2801.5 and its subsectionsPan depth (1 1/2 in.), drain size (3/4 in.) and where the drain ends
Backflow protectionSection P2902P2902.3 lists the device types; P2902.4 and P2902.5 say where each is needed
Pipe support spacingSection P2605.1, Table P2605.1Material row, then horizontal or vertical column
TestingSection P2503DWV, water supply, shower liner and backflow device tests each have their own subsection

Testing is a good example of why the last column matters. Under Section P2503.5.1, a DWV water test fills each section to at least 10 feet above its highest fitting and holds it for 15 minutes. Under Section P2503.7, the water supply is tested at no less than the system's working pressure, or with at least 50 psi of air for piping other than plastic, again for 15 minutes. Same section, different systems, different numbers.

Water heaters: three places, one appliance

Water heaters are the classic multi-chapter topic. Chapter 28 is the plumbing side. Section P2801.2 sends installation to Chapters 20 and 24 as well, and the exam expects you to follow those links.

  • Chapter 28 — drain valves, pans (P2801.5), garage elevation (P2801.6), seismic bracing (P2801.7) and relief valves (P2804).
  • Chapter 20, Section M2005 — general installation and prohibited locations. Fuel-fired water heaters may not go in a room used as a storage closet, and those in bedrooms or bathrooms need a sealed enclosure unless they are direct-vent (M2005.2).
  • Chapter 24, Fuel Gas — Section G2448 (water heaters), Section G2407 (combustion, ventilation and dilution air) and Section G2427 (venting of appliances). The number in parentheses after each G section is the matching International Fuel Gas Code section. It is there for cross-reference only; on the P1 you work from the IRC.

Fixtures that live in the building chapters

Two fixture topics are not in Part VII at all. Required fixtures — a water closet, lavatory, and bathtub or shower for each dwelling unit, and a kitchen sink — are in Section R326. Fixture spacing in toilet, bath and shower spaces is in Section R327 and its figure. Both moved in 2024; in the 2021 IRC they were R306 and R307. And permits, including the plumbing exemptions, are in Section R105.2 in Chapter 1.

A lookup method that works under time pressure

  1. Name the system. Is the question about drainage, venting, traps, supply, a water heater or a fixture? That alone picks the chapter.
  2. Pick one or two keywords. “Trap arm too long” becomes trap, vent, distance. Use the index if the chapter is not obvious.
  3. Read the section, then the table. Many plumbing answers are in a table, but the section above it tells you when the table applies and what it measures.
  4. Check exceptions and notes. Before you mark an answer, read the exceptions under the section and the lettered notes under the table. They change answers more often than you would expect.

Three practice lookups

Run each of these with the book closed first, naming the chapter, then open it and check.

  • “What is the minimum depth of a fixture trap seal?” Traps → Chapter 32 → Section P3201.2. The answer is a range: at least 2 inches and not more than 4 inches.
  • “May a relief valve discharge pipe include a tee?” Water heater → Chapter 28 → Section P2804.6.1, a numbered list. Item 12 rules out valves and tee fittings.
  • “What is the drainage load of a laundry group?” Drainage → Chapter 30 → Table P3004.1. A washer standpipe plus laundry tub is 3 d.f.u. as a group.

Each one takes three moves: system, chapter, section. That is the habit to build.

Using the index without getting lost

When the chapter is not obvious, go to the index at the back of the book. It is alphabetical by topic, and its entries point to section numbers or whole chapters rather than page numbers. Look up the object in the question, not the rule: under “Water Heater” you will find sub-entries for the pan (P2801.5) and relief valves (P2804), and under “Water” the entry for pressure points to P2903.3.

Treat an index entry as a lead, not an answer. In the 2024 IRC (Second Printing), the index lists water heater seismic bracing at P2801.6, but P2801.6 is the garage-elevation section; the bracing rule is P2801.7. Always open the section the index names and confirm it says what you need.

Tables worth tabbing

If tabbing is allowed in your testing setup, a few tables come up again and again in residential plumbing work: Table P3004.1 (drainage fixture units), Table P3005.4.1 and Table P3005.4.2 (drain sizing), Table P3105.1 (trap-to-vent distance), Table P3201.7 (trap sizes), Table P2903.7 and Table P2903.7(1) (water supply fixture units and demand) and Table P2903.9.1 (manifolds). Keep the tabs few and clearly labeled; a book with a dozen good tabs is faster than one with fifty.

A simple tab plan uses two edges of the book. On one edge, put a tab at the start of each chapter from 25 through 32, plus Section M2005 and Chapter 24 for water heaters, so you can jump to any system in one move. On the other edge, tab only the tables listed above, plus Table P2605.1 for pipe support. Write the table number on each tab, not just a topic, because questions and answer explanations refer to tables by number.

For how these chapters line up with the exam weights, see the P1 exam overview. For the numbering traps that catch people who studied an older edition, see common P1 mistakes.

For the exact code language, read the sections on the official ICC Digital Codes site. We cite section identifiers and explain the logic in our own words — always confirm the current text and any local amendments there.

Practice this topic with 2024 IRC-based P1 questions

Create a free account to practice P1 questions with written explanations and 2024 IRC references.

Related guides

Frequently asked questions

Which IRC chapters cover plumbing?
Part VII Plumbing runs from Chapter 25 (Plumbing Administration) through Chapter 33 (Storm Drainage). The P1 content areas map to Chapters 25–32; Chapter 33 storm drainage is not one of the P1 areas.
Where are the gas rules for water heaters in the IRC?
In Chapter 24, Fuel Gas. Section G2448 covers water heaters, G2407 covers combustion, ventilation and dilution air, and G2427 covers venting of appliances. The numbers in parentheses after each G section are the matching International Fuel Gas Code sections, but on the P1 you cite the IRC.
Does the IRC index point to pages or sections?
The index is alphabetical by topic and points to section numbers or whole chapters, not page numbers. Treat each entry as a lead: open the section it names and confirm it covers your question before you answer.